On our way to The Bahamas!

After being pinned down in Savannah for quite a while from bad weather, we finally have a good weather window to make the crossing from Thunderbolt, GA (suburb of Savannah) to Freeport, Grand Bahama. We had a crew member join us yesterday, Abe. He and his wife found out about a hull slot opening for a Vision 444, came to meet Sue and Mira in Oriental, NC for a tour and to hear about our experience, and decided to jump on the open hull slot!

Welcome to the Vision Family Abe and Anna!

Abe has been on standby as we have all collectively waited for good weather. That storm that came up the coast was creating 30-40 knt winds and 12-15 ft waves! That is finally passed and the weather will be a little bumpy, but we have great reaching winds forecasted the whole way there. Should make for a fast sail if that forecast proves true.

We expect to arrive in Lucaya (the non-commercial port right next to Freeport) around mid-day on the 22nd. We'll explore there for a few days and move on, probably to Nassau, where I have to see the US Embassy about getting a new passport. UGH!

I'll add another post soon to cover what we did in Savannah and add one once we arrive in The Bahamas.

Comments

Victron Isolation Transformer - How to lower the output voltage

Re-configuring a Victron Energy isolation transformer This is a companion article to a YouTube video covering the same topic. What are they and why do I need one? Victron Energy isolation transformers are often used on boats that connect to shore power in order to provide a means of providing isolation between the shore power and the AC power that exists on the boat. The transformer sits in between those two worlds and isolates that two power supplies through magnetic flux and an air-gap. The reason this is needed on a marine vessel is because without it, small leakage currents can flow between the earth ground for shore power and the "earth ground" connection on the boat, which is usually connected to water through a propeller shaft, out-drive, sail-drive or sacrificial zincs. That creates a loop and that small leakage current greatly accelerates any galvanic corrosion that naturally happens. Current flows through the water because of the salt content, or even in fresh-wat...

Raising the dinghy, easier!

The Davit System The Vision 444 comes with a Carbon Fiber Davit system that is used to hoist a dinghy. As time has gone on, some of the exact specifics of the davit system have evolved and changed slightly, but for our boat (Hull #11) and the ones near to it, this is how it operates. Two Main Steps First, after attaching the dinghy to a forward and aft attachment line, the davit arms are raised; pivoting on axles which mount the davit to the transom of the boat. This step is accomplished by attaching a line which runs through several blocks to the starboard, aft power winch. Pressing "2" (low speed) on the winch power buttons and raising the davit into its full upright position, where it can be lashed to the boat with Dyneema loops. Second, is to raise the dinghy to be close under the horizontal beams of the davit arms. The dinghy attachment lines, that are attached to the dinghy's bridle, run up through a fixed block at the end of the davit arms and then t...

Vision 444 - How to (hopefully never have to) use a Storm Sail

How to use the Storm Sail on a Vision 444 My fellow Visionary Pierre on Umbono reached out recently wanting to review the steps for deploying the Storm Sail, since he was forecasted to be in less-than ideal sailing conditions in the next day. What better opportunity to write a blog article! This is going out quickly to support Pierre, but I will come back and add pictures and maybe link a video later. Preparation Keep the Storm Sail and everything you need for it somewhere where it is easy to get. We keep ours in the large lazarette under the Cockpit table seating. If you think you might need the Storm Sail, you probably should have the jacklines put out too. The system we use to deploy the Storm Sail reduces the time we need to be forward, but wearing a life vest with harness and being clipped into the lazy jacks is the way to go here. Our Storm sail is in it's own bag with the following: A port sheet attached to the clew with a bowline A starboard sheet attached to the cle...

On A New Tack

Search This Blog